Change Currency: USD

CCD LICENSE PLATE FRAME Mount Rear View Backup Camera (CW144646CI)

$109.99 $59.99

Product Information

THE SIMPLEST INSTALLATION SOLUTION!!!

Just replace your old license plate frame with this new one, wire it and you're done. No inestetic, outcentered holes in your bumper, no outside casings, just a simple license plate frame. The frame itself it's quite sturdy, made of a chrome zinc alloy with a black or chromed finish. It is rust, scratch and water resistant.

When You Purchase Through Us This Is What You'll Get

 

 

Camera Cable Connectors

(Stock Photo Provided By Manufacturer)

Camera Cable Connectors

(Stock Photo Provided By Manufacturer)

Camera Cable Connectors

Power Connector, Vedio Connector, Mirror View Wire

(Stock Photo Provided By Manufacturer)

Camera Cable Connectors

Male Power Lead Plug

 

The Camera Has The Following Special Features

Camera Technical Specifications

CW134087CAI Rear View Camera Dimension

(Stock Photo Provided By Manufacturer)
Frame Approx. 12.3" (L)  x 6.3" (w) x 1" (D)
 
Image Sensor Special 1/4" SHARP CCD Sensor TV System NTSC
Effective Pixels 512 x 492 pixels Resolution 420 TV Lines
Sensing Area 3.6mm x 2.7mm Sync System Internal
Horizontal Sync Frequenc 15,734 KHz Vertical Sync Frequency 60 Hz
Scanning System 2:1 Interlace Minimum Illumination 0 Lux (LED ON)
Video Out Signal 1.0 Vp-p 75 ohm Power Supply DC 12V 
AGC Auto S/N Ratio Better than 48dB
White Balance  Auto Gamma Consumption 0.45
Electronic Shutter 1/60 - 1/10,000 seconds BLC Auto
Current Consumption Max 180mA Lens f=1.7mm/F=2.0
Lens Angle
 
180°
 
Storage Temperature  -40°F - 176°F (-40°C - 80°C) / RH 95% Max
 
Operating Temperature -4°F - 158°F (-20°C - 70°C) / RH 95% Max  Frame Dimension  12.3"(L) x 6.3"(W) x 1"(D)
 
      • One CCD COLOR License Plate IR Weather/Water-Proof Vehicle Rear View Camera with a frame constructed of chrome plated metal 
      • All the necessary cable hookups and Male Power Lead Plug to get your camera up and running.
      • English User Manual
      • License Plate Mount Camera with a license plate frame constructed of chrome plated metal - simply replace your old license plate frame with this new one!
      • Water-proof without extra housing: for part (camera glass lens) exposed to outside ONLY and for normal usage ONLY. Camera body and cables are not designed to be exposed to outside and must be properly sealed against moisture. Incorrect installation and using the product in opposition to the manufacturer's instructions MAY result in loosing water-proof feature.
      • CCD color, Special 1/4" CCD SHARP image sensor WITH 1.7mm lens - that gives you the widest angle and best quality
      • High power, over launch infrared tubs - auto activate at night
      • Super low illumination
      • High resolution 420 TV lines
      • User adjust left/right mirror reverse image - can set to display a reversed camera image on the monitor (for vehicle rear viewing to duplicate the normal view seen in a rear-view mirror) OR a normal view on the monitor (for vehicle front viewing) - connect two-pin jumper connector to the mirror reverse wire to set for normal view
      • Adjustable view, up to 45 degree tilt down
      • EXTRA Wide View Angle 180 Degree with extra wide 1.7mm lens! - Essential to get a wide picture view especially when backing up a towed vehicle or a vehicle with wide turning radius!
      • High power, over launch infrared tubs - auto activate at night, 30 foot night vision!
      • Standard RCA video output - When in need of replacement cables you can simply buy them off the shelves of any store selling video cables.  There's no need to shop around for some "special type" of cable.  The connectors are compatible with this product as they would be with any VCR, DVD player, TV, or Monitor.
      • Uses standard 12V DC power supply found in most land vehicles
      • Caution: The camera is designed to operate within a range of constantly changing voltage levels produced by a vehicle's battery and alternator (post engine ignition) under normal use conditions. Some vehicles have a very high momentary voltage at the vehicle starting time and the excessive voltage generation at that time might cause damage to the camera. If your vehicle tends to emit high voltage levels during ignition you will need to install a fuse/voltage regulator/etc. to protect your camera. Please consult with a professional vehicle audio/video equipment installers if needed.

 

 

 

 

 

Product Code: CW144646CI

Customer Reviews

This product hasn't been reviewed yet. Write a review

 

Mobile Site